 The
VM101 BAT ip alarm adapter allows most Honeywell Ademco
Vista, GE NX (Caddx) and, DSC,
alarm systems to communicate signals over the Internet
to our Virtual Monitoring servers. See our Compatibility
Chart Our Alarm Panel Adapters connect
directly to the alarm panel and do not require a phone
line.
Alerts from My Virtual Monitoring are
sent via voice, text and or email messages which can be
sent to phones/cell/mobile devices. Also allows for Arm/Disarm
of Alarm via Virtual Internet
Keypad (On select panels) Compatibility
Chart
Automatic, end-to-end line supervision
One of the most important feature we offer is
line security — we’ll tell you within a few minutes if
we lose contact with your alarm system (i.e. if your ISP
goes down, or your house line is cut). By contrast, when
your alarm system is plugged into a POTS line (as is traditionally
done), there is no way for the monitoring station to know
if, for example, your telephone line is cut (by an intruder).
You might find out in a few hours if, for example, your
alarm system misses it’s daily test signal. But you won’t
know in real-time.
My Virtual Monitoring's NEW VM101 Wireless Broadband
Alarm Transmitter, Wireless BAT, is a evolutionary
jump in installation over the VM101 BAT. Providing the
same great secure, cost-effective alarm communication
and feature-rich system interaction. The VM101 Wireless
BAT works with the same three major panel manufactures,
Honeywell, DSC and GE as the VM101 BAT. A simple four
wire connection* and a secure ZigBee communication method
to the MVM Gateway, makes the installation of the VM101
Wireless BAT simple and practical. The VM101 Wireless
BAT's low cost, secure two-way communication and wireless
installation provides our customers the most affordable,
fully featured system interaction and non-invasive new
or old construction installation on the market today.
Not available for DSC
Alexor
*DSC panels require an
additional PC-Link cable that is included with every unit.
VoIP Compatible: Our
VM101 BAT ip alarm adapter offers an inexpensive and simple
solution to the #1 problem facing the alarm industry.
VoIP phone service.. Signals can be retransmitted from
the internet to the central station via standard PSTN
telephone lines if you wish. No VoIP phone service required.
Installation made easy. Just
attach 12 VDC power, and connect the VM101 to the control’s
keypad terminals. Plug in the RJ45 Jack to a Broadband
connection, and the installation is complete. Register
the VM101 on My Virtual Monitoring's web site, set up
and verify contacts and then you will start to receive
signals. Compatibility Chart
Homeowners: My Virtual
Monitoring can notify you when your kids get home from
school, the security system is armed and the home is secure
or that there's an emergency, even when you're on vacation.
Have a temperature or water alarm? Be notified when one
of these trip and avoid costly damage.
Business Owners: Want
to know that your employees turned on the alarm system
and your business is secure? My Virtual Monitoring can
send you a notification, not only when the system has
been armed but also when it has been disarmed so you will
know when your employees get in or if someone's comes
in after hours. Give each employee a unique code and know
right away who is turning on or off the alarm.
| FEATURES:
No Telephone Lines Needed
Works with any broadband internet.
Including Cable, DSL, FIOS, Satellite, 3G or 4G
Cellular.
Arm/Disarm Alarm via Internet Keypad
(on select systems) Not
available on DSC Alexor
ipFob Mobile Remote Control for Android,
iPhone (on select systems)
Compatibility Chart. Not
available on DSC Alexor
Automated Telephone Notification
(automated voice) Receive automated voice notifications
to any phone number..... (USA & Canada Only)
Customers outside of North America
who want phone calls from our system can get a USA
phone number and have it forward to them anywhere
in the world for a one time $3.00 set up fee and
$0.99 per month plus the cost of each call forward
to your phone. Click
Here for more information
Text & eMail Messaging Receive
alerts to any cell phone or e-mail address (NOTE:
Text messaging outside of North America is done
by email to text. Check with your cell phone carrier
to make sure they accept email to sms)
Works with any central station. Signals
are retransmitted to the station of your choice
using standard PSTN telephone lines. Or use as a
stand alone solution. No special equipment needed
for the central station.
Super Fast Transmission Speed Signaling
of events in SIA/FSK or Contact ID are handled with
a total of four packets of data, two of which are
acknowledgements for safe signal storage and relay.
This equates to less data packets than other methods
used by other analog adaptors available today and
less demand on your network.
Easy to Install and Set-up Just
attach 12 VDC power, and connect the VM101 to the
control’s keypad terminals. Plug in the RJ45 Jack
to a Broadband connection, and the installation
is complete. Register the VM101 on My Virtual Monitoring's
web site, set up and verify contacts and then you
will start to receive signals.
Plug and Play Automatically Acquires
IP Address. Uses DHCP
No UPS required for the VM101 as
the VM101 gets it's power and backup power from
the alarm panel. You should have a UPS for your
modem and router incase of a power failure.
1 to 20 contacts: Owner, family and friends.
Or even a Guard Service.
Each Contact Includes:
- 1 email address
- 1 TEXT cell phone number
- 2 phone numbers
for automated calls
Specifications:
- Input Voltage 12 Volt DC
- Current Draw: 125mA
- Size: 2 3/4" x 3
|
Our VM101 BAT Broadband
Alarm Transmitter's
operate over any Broadband Internet connection. They do
not require a telephone line or a VoIP account. All that
has to be done is to connect your Ademco Vista, GE NX
or DSC panel to the VM101 BAT, plug into your router and
monitoring can start right away.
 Added
Support for Compass Downloading
Access to Compass Software Now
Included in our Service Plans for Ademco Users. (Check
your email after ordering for instructions to download)
The Broadband
Alarm Transmitter's
(BAT) now have support for downloading/uploading through
the internet using the Compass software This applies to
all Honeywell Vista Series controls that supports Internet
upload/download via ECP.
The system requires a active Broadband
Alarm Transmitter (VM101) that is connected
to your Broadband network and your Honeywell Vista panel
and the Compass software (included). Compatible
Panels for Internet Downloading
|
